上海荣计达仪器科技有限公司

021-61997300 13761118616

累积点滴改进  迈向完美品质

www.rongjida.cn

图片展示
搜索

PM-240D平磨仪

平磨仪是**检测仪器,可作颜料、涂料、油墨行业专用的物理性能检验仪器。整机结构紧凑,外观简洁,转数和负荷变换方便,下班盘装拆简便。采用液晶屏显示,参数设置方便。平磨仪是**标准GB5211.19《着我颜料相对着色力和冲淡的测定目视比较法》中的仪器。

  • 型号: PM-240D

  • 产品参数
  • 型号: PM-240D


平磨仪**检测仪器,可作颜料、涂料、油墨行业专用的物理性能检验仪器。整机结构紧凑,外观简洁,转数和负荷变换方便,下班盘装拆简便。采用液晶屏显示,参数设置方便。平磨仪是**标准GB5211.19《着我颜料相对着色力和冲淡的测定目视比较法》中的仪器。

The flat mill is a testing instrument that can be used as a physical performance testing instrument for the pigment, coating and ink industries. The whole machine has a compact structure, a simple appearance, convenient rotation and load change, and easy assembly and disassembly of the off-duty disk. LCD screen display, convenient parameter setting. The flat mill is the instrument in the standard GB5211.19 "Determination of the relative tinting power and dilution of pigments by visual comparison method".

 

平磨仪技术参数:

★磨盘直径:240mm

★荷   载: 43 kg     64kg    100kg

★砝码重量: 1.75kg    3.5kg    6.42kg

★电源电压: 220VAC 50HZ  

★ 玻璃盘转速:75 转/分±5转/分

★设定圈数显示范围:1~9999

★运转圈数显示范围:0~9999

★累计次数显示范围:0~9999

★外形尺寸: 580*360*480mm

★重量:约80kg

★电动机功率:0.75kw

Technical parameters of flat grinder:

★ Grinding disc diameter: 240mm

★ Load: 43 kg 64 kg 100 kg

★ Weight: 1.75kg 3.5kg 6.42kg

★ Power supply voltage: 220VAC 50HZ

★ Glass plate speed: 75 rpm ± 5 rpm

★ Set lap display range: 1 ~ 9999

★ Display range of running laps: 0 ~ 9999

★ Accumulation times display range: 0 ~ 9999

★ Dimensions: 580 * 360 * 480mm

★ Weight: about 80kg

★ Motor power: 0.75kw

 

平磨仪操作步骤:
★将定量的试样和调和剂放在下磨盘上,用调刀调和成浆,然后将调和好的浆移到下磨盘的**位置,并放下上磨盘,使定位轴芯与定位块扣上,再将偏心手柄向下板,挂上所需砝码。
★合上控制器的电源开关时,蜂鸣器发出“滴”的一声。
★液晶屏显示开机画面:
★按键盘上的“设定”键进入设定圈数的万位,此时万位在闪烁,按下“▲”键万位数值加1,按下“?”键循环移一位。按下“确定”键确定设定圈数,进入功能操作。但设定圈数不为0,否则显示“输入设定圈数”,重新设置。在设定圈数期间不能按下功能键,否则显示设定圈数,重新设置。若“确定”键按下发现设定圈数有误可按下“设定”键重新设置。若确定设定圈数正确,按下“运转”键,此时电动机开始运行。每转动一圈。“运转圈数”自动累计加1。当运转圈数和设定圈数相同时,电动机自动停止运转,此时蜂鸣器发出“嘀嘀嘀”的报警声,“累计次数”自动加1。此时扳动偏心手柄,把磨盘上、下分离,将定位手柄往外拉,同时向上推起,打开上磨盘,观察试样。
★若按照上一次设定的圈数再运转一次,**直接按“运转”按键;如要在中途停机,则可按“停止”按键。若“清零A”则“运转圈数A”计数器会自动清零;若“清零B”则“累计次数B”计数器会自动清零,于此同时会发出“嘀”的一声。要再继续工作只需按“运转”按键,机器将继续运转,直到运转到设定的圈数为止。
★若机器要长时间运转,则应停止计数器计数。此时“运转圈数”会显示“STOP”;假如不想长时间运转,**再按一次“停止计数”按键,机器**恢复到原来计数状态。
★若机械运转过程中按“设定”键,整机将停止运行。同时“设定圈数”万位闪烁、“清零A”和“清零B”的数值。
★如需水冷,则接通上磨盘的水嘴。

Flat grinding machine operation steps:

★ Put the quantitative sample and blending agent on the lower grinding disc, use the knife to adjust the slurry, then move the conditioned pulp to the position of the lower grinding disc, and lower the upper grinding disc, so that the positioning shaft core and the positioning block buckle , And then eccentric handle to the lower plate, hanging the required weight.

★ When the power switch of the controller is closed, the buzzer will make a "drop".

★ LCD screen displays the startup screen:

★ Press the "Set" key on the keyboard to enter the tens of thousands of laps. At this time, the tens of digits are blinking. Press the "▲" key to increase the number of digits by 1. Press the "?" Key to cycle through one position. Press the "OK" key to confirm the set number of turns and enter the function operation. However, the number of set laps is not 0, otherwise “Enter the number of set laps” is displayed and reset. During the setting of the number of laps, the function key cannot be pressed, otherwise the set number of laps will be displayed and reset. If you press the "OK" key and find that the set number of turns is wrong, you can press the "Set" key to reset it. If it is determined that the set number of turns is correct, press the "Run" key, and the motor starts to run. Every turn. "Run laps" is automatically increased by one. When the number of rotations and the set number of rotations are the same, the motor will automatically stop running. At this time, the buzzer will sound an alarm of ",", and the "cumulative number" will automatically increase by 1. At this time, pull the eccentric handle to separate the upper and lower sides of the grinding disc, pull the positioning handle outwards, at the same time push it upward, open the upper grinding disc, and observe the sample.

★ If you run again according to the number of laps set last time, ** directly press the "Run" button; if you want to stop in the middle, you can press the "Stop" button. If "clear A", the "turns A" counter will be automatically cleared; if "clear B", the "accumulation times B" counter will be automatically cleared, and at the same time, a "beep" sound will be issued. To continue working just press the "Run" button, the machine will continue to run until it reaches the set number of laps.

★ If the machine is going to run for a long time, stop the counter. At this time, the “number of running laps” will display “STOP”; if you do not want to run for a long time, ** press the “Stop Counting” button again, the machine ** will return to the original counting state.

★ If you press the "Set" key during the machine running, the whole machine will stop running. At the same time, the digits of “Setting laps” flash, the values of “Clear A” and “Clear B”.

★ If water cooling is required, connect the water nozzle of the upper grinding disc.


PM-240D平磨仪

长按图片可保存到相册

图片加载中,请稍等 ...
长按图片保存/分享
询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

PM-240D平磨仪

立即询盘
询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

推荐产品

上海荣计达仪器科技有限公司

电话:021-61997300

传真:021-34795918

邮箱:289239104@qq.com

地址:上海市闵行区浦江镇联胜路189号 

邮编:201112 

图片展示

版权所有:上海荣计达仪器科技有限   公司地址:上海市闵行区浦江镇联胜路189号 邮编:201112   沪ICP备11009963号