上海荣计达仪器科技有限公司

咨询电话:137-6111-8616


DTM-15电动脱模器

电动脱模器适用于多种土、混合料的圆形试模试件的脱模,电动脱模器尤其可满足水泥混合料强度试件的脱模要求,其大载荷可达150KN、。这种电动脱模器完全采用模块化设计,充分利用现代微电子技术将各功能模块高度集成,主控箱既完成自身数据自动采集,又能协调本系统其它扩展箱按设定程序自动工作。

  • 型号: DTM-15

  • 产品参数
  • 型号: DTM-15

电动脱模器适用于多种土、混合料的圆形试模试件的脱模,电动脱模器尤其可满足水泥混合料强度试件的脱模要求,其大载荷可达150KN、。这种电动脱模器完全采用模块化设计,充分利用现代微电子技术将各功能模块高度集成,主控箱既完成自身数据自动采集,又能协调本系统其它扩展箱按设定程序自动工作。

The electric demoulder is suitable for demoulding circular test specimens of various soils and mixtures. The electric demoulder can especially meet the demoulding requirements of the cement mixture strength specimens, and its large load can reach 150KN. This type of electric demoulder completely adopts a modular design and makes full use of modern microelectronic technology to highly integrate various functional modules. The main control box not only completes its own automatic data collection, but also coordinates the other expansion boxes of this system to work automatically according to the set program.


电动脱模器产品用途:

★抗压试模:¢150Х230mm   ¢100Х180mm  ¢50Х130mm

★轻重型土工击实试模:¢152Х170mm   ¢100Х127mm

★马歇尔击实试模:¢101.6Х87mm

Product use of electric stripper:

★ Compression test mold: ¢ 150Х230mm ¢ 100Х180mm ¢ 50Х130mm

★ Light and heavy earthwork compaction test mold: ¢ 152Х170mm ¢ 100Х127mm

★ Marshall compaction test mold: ¢ 101.6Х87mm


电动脱模器技术指标:

★脱模器丝杠上升速度: 70mm/min  

★脱模器丝杠下降速度: 70mm/min  

★脱模器丝杠A大移动距离: 240mm  

★脱模器丝杠A大上升**限距离: (L) 270mm  

★脱模器丝杠A底下降**限距离: (L) 30mm  

★脱模器丝杠A大脱模力: 150KN 

★重量:约100kg

Technical indicators of electric demoulder:

★ The lifting speed of the ejector screw: 70mm / min

★ Drop speed of ejector screw: 70mm / min

★ Large moving distance of ejector screw A: 240mm

★ A large rise of the ejector screw A ** Limit distance: (L) 270mm

★ The bottom of the ejector screw A is lowered ** Limit distance: (L) 30mm

★ Removal force of mold release screw A: 150KN

★ Weight: about 100kg


电动脱模器主要结构和工作原理:

主要由机架、 液压系统、 压力表及电器系统组成

★机架部分:

主要由横梁 、立柱、 托盘、 外壳、 底座等附件组成。横梁可安装脱模和制件附件,用于各种试模脱模用,油缸柱塞中孔可安装各种附件便于制件和脱模,托盘是用于脱模时模具的定位和支撑。

★液压系统

由液压泵、 送油阀、 回油阀 、油箱、 滤油器及油管和接头组成。液压泵为高压柱塞泵,流量为1.2L/min,额定压力40MPa,由0.75KW电机直接驱动,固定在油箱上。

回油阀和送油阀分别安装在前面板的左右面,均由手轮直接操作,右侧送油阀能调节活塞上升速度,左侧回油阀用于油缸下降回油,送油阀上设有安全阀,过载时可溢流起安全作用。

★压力表:

电动液压脱模器压力表为2.5级耐震压力表,用于测量缸内工作压力,使用时注意压力值严禁超过40MPa,以防损毁机件。

★电器部分

由电动机、 启动按钮 、停止按钮 、熔断器 、继电器等组成

Main structure and working principle of electric demoulder:

Mainly composed of frame, hydraulic system, pressure gauge and electrical system

★ Rack part:

It is mainly composed of beams, columns, trays, shells, bases and other accessories. Beams can be equipped with demoulding and accessory parts for demoulding of various test patterns. Various accessories can be installed in the center of the cylinder plunger to facilitate parts and demoulding. The tray is used for positioning and supporting the mould during demoulding.

★ Hydraulic system

It consists of a hydraulic pump, an oil delivery valve, an oil return valve, an oil tank, an oil filter, an oil pipe and a joint. The hydraulic pump is a high-pressure plunger pump with a flow rate of 1.2L / min and a rated pressure of 40MPa. It is directly driven by a 0.75KW motor and fixed on the fuel tank.

The oil return valve and the oil delivery valve are respectively installed on the left and right sides of the front panel, and are directly operated by the handwheel. The right oil delivery valve can adjust the rising speed of the piston, and the left oil return valve is used to lower the oil return valve on the oil cylinder. Equipped with safety valve, it can overflow for safety when overload.

★ Pressure gauge:

The electro-hydraulic ejector pressure gauge is a 2.5-level shock-resistant pressure gauge, which is used to measure the working pressure in the cylinder. When using it, pay attention that the pressure value is strictly prohibited to exceed 40MPa to prevent damage to the parts.

★ Electrical parts

Composed of motor, start button, stop button, fuse, relay, etc.


电动脱模器注意事项:

1、严禁不加油,使油泵空转

2、使用前必须排尽系统内空气,才能使用

3、使用时应观察压力表示值,严禁超过40MPa当接近时应迅速切断电源或打开回油阀

4、出厂安全阀以调好,勿动

5、使用电动液压脱模器前必须仔细阅读使用说明书

Note for electric ejector:

1. It is strictly forbidden to keep the oil pump idling without adding oil.

2. The air in the system must be exhausted before use.

3. Observe the pressure indication value during use. It is strictly prohibited to exceed 40MPa. When approaching, the power should be cut off quickly or the oil return valve should be opened.

4, factory safety valve to adjust, do not move

5.Please read the instruction manual carefully before using electric hydraulic ejector


DTM-15电动脱模器
电动脱模器适用于多种土、混合料的圆形试模试件的脱模,电动脱模器尤其可满足水泥混合料强度试件的脱模要求,其大载荷可达150KN、。这种电动脱模器完全采用模块化设计,充分利用现代微电子技术将各功能模块高度集成,主控箱既完成自身数据自动采集,又能协调本系统其它扩展箱按设定程序自动工作。
长按识别二维码查看详情
长按图片保存/分享

DTM-15电动脱模器

询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

扫一扫关注我们

Copyright @ 2018 上海荣计达仪器科技有限公司.All Rights Reserved   沪ICP备11009963号-4     

Copyright @ VillaGrandis All Rights Reserved某某某有限公司版权所有        

ICP备案号180006020号-3

 

客服中心
热线电话
13761118616
上班时间
周一到周日
二维码